by

BFT, Carbon and stainless steel,Flanged EN or ASME ISO or NPT Threaded sockets

BFT
The BFT boiler feed tank is one of the most important devices in a boiler room. Its main function is to store the make-up water and condensate, assuring a reserve of treated water to supply to the steam boilers. The make-up water has to be softened to prevent scale formation on the boiler and the oxygen also has to be removed, so that corrosion in the boiler and steam system is avoided.

MATERIAL: Carbon and stainless steel
CONNECTIONS:
Flanged EN or ASME
ISO or NPT Threaded sockets
MAX. ALLOWABLE PRESSURE: 0,5 bar
MAX. ALLOWABLE TEMPERATURE: 120 ºC

by

BV, Carbon and stainless steel, Flanged EN PN16 or ASME

BV
The ADCA BV series blowdown vessels are used in modern boiler houses to cool hot wastewater and steam boiler blowdown before discharging them into a pit or
drain. If flash steam can not be recovered or discharged to the atmosphere, an additional condensing water spray system (optional) can be supplied. It is fitted into the top of the unit and can be controlled by a thermostat.

MATERIAL: Carbon and stainless steel
CONNECTIONS: Flanged EN PN16 or ASME
MAX. ALLOWABLE PRESSURE: 7 bar
MAX. ALLOWABLE TEMPERATURE: 180 ºC

by Mats Mats

BEX, Carbon, stainless steel

BEX
The ADCA BEX series blowdown expansion and cooling units are used in modern boiler houses to cool hot wastewater and steam boiler blowdown before discharging them into a pit or drain. The wastewater is discharged into the unit, which is at atmospheric pressure, and the cooling water enters through a control valve controlled by a thermostat, mixing it with the hot water.

MATERIAL: Carbon and stainless steel
CONNECTIONS:
Threaded ISO 7 Rp
Flanged EN or ASME
MAX. OPERATING PRESSURE: 0,5 bar
MAX. ALLOWABLE TEMPERATURE: 120 ºC

by Mats Mats

FCD, Stainless steel

FCD
The ADCA flash condensing heads are designed to promote energy efficiency on new or existing systems. Mixing the flash steam with the boiler make-up water allows the energy within the flash steam to be fully absorbed into the water and therefore reduces energy waste that normally occurs from the discharge of flash steam through a vent.

MATERIAL: Stainless steel
CONNECTIONS:
Threaded ISO 7 Rp
Flanged EN or ASME
Different connections on request
MAX. ALLOWABLE PRESSURE: 0,5 bar
MAX. RELATED TEMPERATURE: 120 ºC

by Mats Mats

TDG, Carbon, stainless steel

TDG
The TDG series tray-type thermal deaerators are designed to heat boiler feed water and reduce oxygen and carbon dioxide levels (oxygen levels in the feed water of less than 0,02 mg/l – 0,02 ppm can be achieved). Remaining oxygen can be completely removed using oxygen-scavenging chemicals. Basically, the complete system consists of a storage vessel, a deaeration section and a vent.

MATERIAL: Carbon and stainless steel
CONNECTIONS:
Flanges EN or ASME
Sockets BSP or NPT
Different connections on request
MAX. ALLOWABLE PRESSURE: 0,5 bar
MAX. ALLOWABLE TEMPERATURE: 120 ºC

by Mats Mats

ADG, Flanged EN

ADG
The ADCATherm atmospheric semi-deaerators are designed to heat boiler feed water and to reduce oxygen and carbon dioxide (oxygen values in the feed water of less than 1,6 mg/L can be achieved). Remaining oxygen can be completely removed using oxygen-scavenging chemicals. Basically, the complete system consists of a storage vessel, a deaeration head section and a vent.

CONNECTIONS:
Flanged EN or ASME
Sockets BSP or NPT
MAX. ALLOWABLE PRESSURE: 0,5 bar
MAX. RELATED TEMPERATURE: 120 ºC

by Mats Mats

RVST,Carbon and stainless steel

RVST
The flash vessel is the main component in any flash recovery system. It can be used in all steam plants where high-pressure condensate is reduced to a lower pressure, so that flash steam is formed by re-evaporation. This steam can be used in a low pressure process or heating equipment.

MATERIAL: Carbon and stainless steel
SIZES: RVST08, RVST12, RVST16, RVST18
CONNECTIONS: Flanged EN PN16
MAX. OPERATING PRESSURE: 16 bar
MAX. OPERATING TEMPERATURE: 250 ºC

by Mats Mats

RV, Carbon and stainless steel

RV
The flash vessel is the main component in any flash recovery system. It can be used in all steam plants where high pressure condensate is reduced to a lower pressure, so that flash steam is formed by reevaporation. This steam can be used in low pressure process or heating equipments.

MATERIAL: Carbon and stainless steel
SIZES: RV06, RV08, RV12, RV16 and RV18
CONNECTIONS: Flanged EN PN16
MAX. OPERATING PRESSURE: 16 bar
MAX. OPERATING TEMPERATURE: 250 ºC