ADG
The ADCATherm atmospheric semi-deaerators are designed to heat boiler feed water and to reduce oxygen and carbon dioxide (oxygen values in the feed water of less than 1,6 mg/L can be achieved). Remaining oxygen can be completely removed using oxygen-scavenging chemicals. Basically, the complete system consists of a storage vessel, a deaeration head section and a vent.
CONNECTIONS:
Flanged EN or ASME
Sockets BSP or NPT
MAX. ALLOWABLE PRESSURE: 0,5 bar
MAX. RELATED TEMPERATURE: 120 ºC
RVST
The flash vessel is the main component in any flash recovery system. It can be used in all steam plants where high-pressure condensate is reduced to a lower pressure, so that flash steam is formed by re-evaporation. This steam can be used in a low pressure process or heating equipment.
MATERIAL: Carbon and stainless steel
SIZES: RVST08, RVST12, RVST16, RVST18
CONNECTIONS: Flanged EN PN16
MAX. OPERATING PRESSURE: 16 bar
MAX. OPERATING TEMPERATURE: 250 ºC
RV
The flash vessel is the main component in any flash recovery system. It can be used in all steam plants where high pressure condensate is reduced to a lower pressure, so that flash steam is formed by reevaporation. This steam can be used in low pressure process or heating equipments.
MATERIAL: Carbon and stainless steel
SIZES: RV06, RV08, RV12, RV16 and RV18
CONNECTIONS: Flanged EN PN16
MAX. OPERATING PRESSURE: 16 bar
MAX. OPERATING TEMPERATURE: 250 ºC
MLI
The MLI series of bypass type magnetic level indicators were designed for continuous level indication and/or control in ADCA ECRU units and other special SKID mounted packages.
The indicators can be equipped with multiple MSB reed switches for alarm purposes or a side mounted level transmitter for continuous level monitoring.
FRECO
The ADCATtherm FRECO – flash steam heat recovery unit – is a skid mounted package unit to facilitate heat recovery from flash steam, condensate or both. The Freco is especially recommended for heating a continuous flow of fluid, such as make-up water to a boiler feedwater system. Non-continuous flow applications may require additional recirculation, relief valves, or other devices, to avoid system damage due to overheating and consequent overpressure.
ECRUV
The ADCAMat ECRUV series electric condensate recovery units are recommended in the transfer of high-temperature water such as hot condensate, to a higher elevation or pressure. This condensate is usually used as boiler feedwater. The standard models are prepared for flows up to 4 m³/h. The units are composed of a vertical condensate vessel (receiver), a metallic support frame, electric pump, level controls, valves, prewired control panel and pipework for connections between the different elements of the units.
SI115
The SI series steam injectors from ADCA are condensate injectors. They ensure low noise and vibration and rapid heating of still or flowing fluids in basins and vessels, due to direct steam injection. Steam enters through the inlet housing, passes along the center of the heater, mixing with the cool water, which is drawn in through radial holes.
MATERIAL: Austenitic stainless steel
SIZES: 1/2”
CONNECTIONS: Threaded ISO 7 Rp
MAX. OPERATING PRESSURE: 17 bar
MAX. OPERATING TEMPERATURE: 95 ºC
RATING: PN 25
SI20
The SI20 series steam injectors from ADCA are condensate injectors. They ensure low noise and vibration and rapid heating of still or flowing fluids in basins and vessels due to direct steam injection.
SIZES: 3/4”
CONNECTIONS: Female screwed ISO 7/1 Rp
MAX. OPERATING PRESSURE: 8,5 bar
MAX. OPERATING TEMPERATURE: 180 ºC
PPT14
The ADCAMat PPT14 automatic pump trap is especially recommended where stall condition may occur due to poor steam trap condensate discharge capacity, caused by temporary insufficient pressure drop. The equipment combines the features of a float steam trap and a pressure operated pump, in one single unit.
MATERIAL: Carbon and stainless steel
SIZES: 11/2” x 1” and 2” x 11/2”, DN 40 x 25 and DN 50 x 40
CONNECTIONS:
Flanged EN PN 16 and ASME Class 150
Threaded ISO 7 Rp
