Processindustri Produkter - Industriventiler För Tillverkningsindustri, Verkstadsindustri, Tung Industri i Sverige
1
Yes
None
1
1000000
Search...
/produkter/
Thumbnail

Produkt Val

Ångejektorer
Pneumatiska ställdon med tillbehör
Reducerventiler
Ång och kondensatutrustning
Backventiler
Backventiler (Non Return Valve GA 015, GB 015)
Backventiler (Non Return Valve GA 015, GB 015) Image

NON RETURN VALVE GA 015, GB 015, GB 019 – Little dimensions and low weights. Face to face acc.to DIN EN 558-1 Series 49 (DIN 3202 K4). Opening pressure from 20 to 500 mBar. Usable also as vacuum breacker, overpressure and bottom valve. No leackage with soft seat and acc.to DIN 3230 BN3 with metal seat. Low head losses.

Backventiler - (Non Return Valve GB 021 - 023)
Diagram GA 015, GB 015, GB 019, GB 021& GB 023
Backventiler - (Non Return Valve GS 011, 015)
Backventil - BAS 102
Backventil - BAS 202
Backventil - BAS 302
Backventiler (Non Return Check Valve)
Backventiler (Non Return Check Valve) Image

CHECK VALVE FEATURES THAT THE PIPING ENGINEER IS LOOKING FOR.   

* Tight shut off under minimum back pressure.

* Quick response to no-flow or reverse flow conditions. Low resistance to forward flow.

* Lightweight construction.

* Ease of installation with unskilled operators.

* No maintenance. It is a stop silent valve.

* It stops the reverse flow and is completely silent in its operation, preventing water hammer.

Smutsfilter
Strainer PN 20, Y-type, brass MS 58, 30 Bar
Strainer PN 20, Y-type, brass MS 58, 30 Bar Image

Strainer PN 20, Y-type with screwed ends and drain plug.

Materials, Body: brass MS 58
Screen: stainless steel 1.4301
Connection: screwed ends DIN 259
Test pressures: 30 bar
Specials: Brass fittings are not approved for use in drinking water installations!

Strainer 800 lbs (~ PN100), Y-type, forged steel A 105N, 205 Bar
Strainer 800 lbs (~ PN100), Y-type, forged steel A 105N, 205 Bar Image

Strainer 800 lbs (~ PN100), Y-type, screwed ends and drain-plug 1/2″ in cover.

Materials, Body: forged steel A 105N,
Screen: stainless steel AISI 316
Gasket: graphit reinforced
Connection: screwed ends BSP
Test pressures: 205 bar

Strainer PN 40 Y-type, with screwed ends, stainless steel 1.4408, 60 Bar
Strainer PN 40 Y-type, with screwed ends, stainless steel 1.4408, 60 Bar Image

Strainer PN 40 Y-type, with screwed ends

Materials: Body: stainless steel 1.4408, Screen: stainless steel perforated plate 1.4408
Gasket: PTFE
Connection: screwed ends BSP
Test pressures: 60 bar

Strainer 800 lbs (~ PN 100), Y-type, stainless steel AISI 316, 205 Bar
Strainer 800 lbs (~ PN 100), Y-type, stainless steel AISI 316, 205 Bar Image

Strainer 800 lbs (~ PN 100), Y-type, screwed ends and drain-plug 1/2″ in cover.

Materials: Body: stainless steel AISI 316.
Screen: stainless steel AISI 316.
Gasket: graphite reinforced.
Connection: screwed ends BSP.
Test pressures: 205 bar.

Strainer PN 63 Y-type, butt-weld-ends, cast steel GP 240GH), 96 Bar
Strainer PN 63 Y-type, butt-weld-ends, cast steel GP 240GH), 96 Bar Image

Strainer PN 63 Y-type, butt-weld-ends and drain-plug 1/2″ in cover.

Materials: Body: cast steel GP 240GH).
Screen: stainless steel 1.4301.
Gasket: graphit reinforced.
Connection: butt-weld-ends DIN 3239 Form C.
Test pressures: 96 bar.

Strainer PN 160 Y-type, butt-weld-ends, cast steel GP 240GH), 240 Bar
Strainer PN 160 Y-type, butt-weld-ends, cast steel GP 240GH), 240 Bar Image

Strainer PN 160 Y-type, butt-weld-ends and drain-plug 1/2″ in cover.

Materials: Body: cast steel GP 240GH).
Screen: stainless steel 1.4301.
Gasket: graphit reinforced.
Connection: butt-weld-ends DIN 3239 Form C.
Test pressures: 240 bar.

Flottörventiler
Flottörventil ESV-80 F-F (FloatValve ESV-80 F-F)
Flottörventil ESV-80 F-G (FloatValve ESV-80 F-G)
Flottörventil ESV 80 G-G (Float valve ESV 80 G-G)
Flottörventil ESV 80 G-G (Float valve ESV 80 G-G) Image

Flottörventil ESV 80 G-G

Flottörventil-KSV-10 (Float-Valve-KSV-10)
Flottörventil-KSV-80 (Float-Valve-KSV-80)
Flottörventil RSV-g (Float-Valve-RSV-g)
Flottörventil RSV-g (Float-Valve-RSV-g) Image

Flottörventil typ RSV-g

Flottörventil-RSV-O (Float-Valve-RSV-O)
Flottörventil-RSV-VA (Float-Valve-RSV-VA)
Flottörventil-SV-26. (Float Valve SV 26)
Flottörventil SV-45 (FloatValve-SV-45)
Kulventiler
3-pieceType A20D/AF20D / DN10-DN100 / 3/8"-4" (3-Piece Ball Valve)
3-pieceType A20D/AF20D / DN10-DN100 / 3/8"-4" (3-Piece Ball Valve) Image

3-PIECE BALL VALVES SERIES A20D / AF20D with full or reduced bore antistatic, with ISO-top flage for direct mounting of an actuator. Stainless steel 1.4408 / CF8M Carbon steel 1.0619 / A216 WCB

2-piece Type AF90D / DN15-DN100 long pattern (Flanged Ball Valves)
2-piece Type AF90D / DN15-DN100 long pattern (Flanged Ball Valves) Image

2-pieces DIN-Flanges Ball Valve long pattern,  full bore.  with double Gasket System FireSafe acc. BS6755 Part2. , TA-Luft and SIL 2 tested and FDA conform. Antistatic, with ISO connection for direct mounting for Actuator. With locking device.

2-piece Type AF94D / DN15-DN100 short pattern (Flanged Ball Valves)
2-piece Type AF94D / DN15-DN100 short pattern (Flanged Ball Valves) Image

2-pieces DIN-Flanges Ball Valve short pattern, full bore.  with double Gasket System FireSafe acc. BS6755 Part2. , TA-Luft and SIL 2  tested and FDA conform. Antistatic, with ISO connection for direct mounting for Actuator. With locking device.

Type 80D / DN15-DN100
Type 80D / DN15-DN100 Image

Wafer type A80D ball valve with full bore, with ISO mounting pad for direct mounting of pneumatic or electrical actuator. FIRESAFE-design (with graphite gaskets) and antistatic device.  With locking device

3-piece Type JBSM / DN15-DN50 / 1/2"- 2" (metal seated ball valve)
3-piece Type JBSM / DN15-DN50 / 1/2"- 2" (metal seated ball valve) Image

3-piece metal seated ball valve, full bore, antistatic device with ISO-mounting pad for mounting of pneumatic or electric actuators. With locking device

V-Port Segment Type JSB / DN25 - DN400 / 1 (metal seated ball valves)
V-Port Segment Type JSB / DN25 - DN400 / 1 (metal seated ball valves) Image

1-piece Trunnion Design DIN PN16/40, or ANSI class150/300, DIN sizes  DN25 – DN400 and ANSI  1inch – 16inch, for Control- or Shut off – Applications, soft- and metal seated Design, with ISO mounting pad acc. ISO5211, anti-blowout-system, Antistatic, Face to Face dimensions acc. ISA S75.04. For Applications up to 350°C.

Floating Type JBFM / DN15-DN250 / 1/2"-10"(metal seated ball valves)
Floating Type JBFM / DN15-DN250 / 1/2"-10"(metal seated ball valves) Image

2-pieces metal seated DIN-/ANSI Flange Ball Valve PN16/40, ANSI class 150 – 300, DIN-Face to face dimension acc. EN558-1, row 27 or ANSI-dimensions, PN100/class 600 on request, full port. FireSafe acc. nach ISO 10497 certified. Antistatic, with ISO connection for  Actuator mounting kit. With locking device. Different body materials and designs available for applications up to 550 ° C.

Kägelventiler
Kägelventiler Protek-2430 DN 15-25 (Globe Valve bellows sealed with flanges)
Kägelventiler Protek-2430 DN 15-25 (Globe Valve bellows sealed with flanges) Image

GLOBE VALVE – Cat 218M, Cat 450M bellows sealed with flanges.

Kägelventiler 2430 DN 32-100 (Globe Valve bellows sealed with flanges)
Kägelventiler 2430 DN 32-100 (Globe Valve bellows sealed with flanges) Image

GLOBE VALVE – Cat 218M, Cat 222M bellows sealed with flanges

Pneumatiska ställdon med tillbehör
Pneumatic Actuators Type 1, Features & Benefits
Pneumatic Actuators Type 1, Features & Benefits Image

Pneumatic Actuators Type 1
Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR). Body of Anodized Aluminum in black colour as standard, other finishes avialable. This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR

Pneumatic Actuators Type 1, 0 -90º WM 1
Pneumatic Actuators Type 1, 0 -90º WM 1 Image

Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR).

Body of Anodized Aluminum in black colour as standard, other finishes avialable.

This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves.

The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR

Pneumatic Actuators Type 1, WM 2, 4, 8, 12, 20 and 35
Pneumatic Actuators Type 1, WM 2, 4, 8, 12, 20 and 35 Image

Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR).

Body of Anodized Aluminum in black colour as standard, other finishes avialable.

This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves.

The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR

Pneumatic Actuators Type 1, WM 250
Pneumatic Actuators Type 1, WM 250 Image

Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR).

Body of Anodized Aluminum in black colour as standard, other finishes avialable.

This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves.

The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR

Pneumatic Actuators Type 1, WM 400
Pneumatic Actuators Type 1, WM 400 Image

Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR).

Body of Anodized Aluminum in black colour as standard, other finishes avialable.

This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves.

The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR

Pneumatic Actuators Type 1, 0 -90º Technical Data, summary
Pneumatic Actuators Type 1, 0 -90º Technical Data, summary Image

Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR).

Body of Anodized Aluminum in black colour as standard, other finishes avialable.

This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves.

The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR

Pneumatic Actuator Type 1, 0 -180º, WM 4, 8, 12, 20 and 35 & Technical Data, summary
Pneumatic Actuator Type 1, 0 -180º, WM 4, 8, 12, 20 and 35 & Technical Data, summary Image

Compact rack and pinion actuator, Type 1, for half turn movement and modulating, only available as Double Acting (DA).

Body of Anodized Aluminum in silver colour as standard.

This actuator is generally recommended to for use with thee way valves with rotary motion between 0-180º turning angle.

The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR.

Chemically Nickel Impregnated Actuators Type 1, CNI
Chemically Nickel Impregnated Actuators Type 1, CNI Image

The high density Nickel Alloy that is used and the added PTFE gives the actuators more resistance to chemical attacks and improves the lifespan.

The production process makes it possible to impregnate also all internal surfaces of the CNI actuators.

From the beginning it was specifically developed for the Food, Beverage and Pharmaceutical industries, now approved by FDA (Food and Drug Administration, USA) for use in the Food & Beverage Industries.

Increased corrosion resistance
CNI actuators are designed to provide the best corrosion resistance possible.

This highly competitive Stainless Steel alternative is an ideal choice for tough environments

Pneumatic Actuators Type 2, Features & Benefits and Body Adaptor Kit
Pneumatic Actuators Type 2, Features & Benefits and Body Adaptor Kit Image

Body Adaptor Kit, BAK
Type 2 has a unique design, it is fitted with a BAK (Body Adaptor Kit).

The integral Body Adaptor Kit, which is interchangeable with a wide range of valves (metric, imperial or customer designed) for direct mounting by using an interchangeable insert sleeve.

The Kit contains body adaptor, sleeve, key, stop adjustment bearing, circlip, bolts and screws.
Stainless Steel Sleeves
All Driveshaft’s in WM Actuators are machined from solid bar.

The Sleeves/Drive inserts, easily replaceable, enables actuators to be directly mounted onto suitable valves and eliminates the need for a bracket and coupling, type mounting kit.

Standard actuators are fitted with square sleeves in accordance with ISO 5211 (or DIN 3337), but a wide variety of other inserts are also available.

Special inserts may have oversize or undersize squares, double-D and shaft key way forms.

The Sleeves are always made of Stainlees Steel, AISI 303/304.

Pneumatic Actuators Type 2, WM 35, 55, 70, 100 and150
Pneumatic Actuators Type 2, WM 35, 55, 70, 100 and150 Image

Pneumatic Actuators Type 2
Compact rack and pinion actuator, Type 2, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR).

Body of Anodized Aluminum in black colour as standard, other finishes avialable.

This actuator is generally recommended to ”large” Butterfly valves.

The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR.

Pneumatic Actuators Type 2, Tecnical Data, summary
Pneumatic Actuators Type 2, Tecnical Data, summary Image

Pneumatic Actuators Type 2

Urkopplingsbar Handväxel (Manual Override Gear)
Urkopplingsbar Handväxel (Manual Override Gear) Image

Manual Override with declutch mechanism for Double Acting (DA) and Spring Return (SR) pneumatic actuators.
For TT Actuators, movement 0-90º size:

ITG-050: DA size 8 to 35
ITG-050: SR size 8 to 20
ITG-060: DA size 35 to 55
ITG-060: SR size 35
ITG-080: DA size 70 to 150
ITG-080: SR size 55 to 70
ITG-100: DA size 250
ITG-100: SR size 100 to 150
MOR-5100: DA size 400
MOR-5100: SR size 250

Digital Positioner PMV Type D3
Digital Positioner PMV Type D3 Image

Digital Positioner Type D3
Digital positioners, often with the display and keypad to enter settings. Advantages are that the auto calibration setting is accurate regardless of who makes the calibration

Pneumatic Positioner PMV Type P5
Pneumatic Positioner PMV Type P5 Image

Pneumatic Positioner Type P5
For single or double acting application, this modular design allows for the simple addition of I/P converters and/or a feedback unit with a variety of feedback options

Electropneumatic Positioner PMV Type EP5
Electropneumatic Positioner PMV Type EP5 Image

Electropneumatic Positioner Type EP5
This compact and sturdy unit is designed for maximum performance in all types of environments.

The EP5 is available in Standard, Intrinsically Safe and Explosion Proof versions

Feedback unit F5 for Positioners Type P5 and EP5, 4-20 mA or Potentiometer
Feedback unit F5 for Positioners Type P5 and EP5, 4-20 mA or Potentiometer Image

Feedback unit Type F5
For position feedback to P5 and EP5, the F5 unit offers the ability to change switches between mechanical and proximity, a potentiometer or a 4-20 mA transmitter to the P5 base pneumatic positioner.

The IP66 modular housing needs no special mounting pieces and is O-ring sealed. F5 mounts direct on top of P5/EP5 positioner.

Feedback unit F5 for Positioners Type P5 and EP5, Endstop indication
Feedback unit F5 for Positioners Type P5 and EP5, Endstop indication Image

Feedback unit Type F5
For position feedback to P5 and EP5, the F5 unit offers the ability to change switches between mechanical and proximity, a potentiometer or a 4-20 mA transmitter to the P5 base pneumatic positioner.

The IP66 modular housing needs no special mounting pieces and is O-ring sealed. F5 mounts direct on top of P5/EP5 positioner.

Pneumatic Positioner type QS-P2G-LT-RE
Pneumatic Positioner type QS-P2G-LT-RE Image

QS-P2G-LT-RE
Remote mounted, External contactless hall effect feed-back with 2 meter cable.
No visual position indicator or display.
Analogue input: 1, V or mA
Manual function, open/close

Consoles & 7-pol IP67 (FM) connector for Supply & Analogue signals not included.

Supplier Pat No: PKV-7129

Mounting Kits for Positioners PMV, NAMUR
Combined Filter-Regulator, Type 107
Solenoid Valve Joucomatic Type G551 5/2-3/2 Namur, Monostable
Solenoid Valve Joucomatic Type G551 5/2-3/2 Namur, Monostable, Explosion Proof, EEx ”m”
Solenoid Valve Joucomatic Type G356 3/2 1/8
Solenoid Valve Joucomatic Type G356 3/2 1/8
Speed Reducer
Ljuddämpare (Silencers)
Push-in Couplings
Manual Override Type ITG 050-080, OPERATION MANUAL
Manual Override Type ITG 050-080
Limit Switch box, Type ITS100, Mechanical
Limit Switch box, Type ITS100, Mechanical - CNI
Limit Switch box, Type ITS110, Inductive
Limit Switch box, Type ITS120, Inductive
Limit Switch box Type ITS300, Mechanical Explosion proof
Limit Switch box Type ITS305, Potentiometer Explosion proof
Limit Switch box Type ITS310, Inductive Explosion proof
Limit Switch box Type ITS320, Inductive Explosion proof
Limit Switch box Type ITS500, Mechanical Explosion proof, Stainless Steel
Limit Switch box Type ITS510, Inductive Explosion proof, Stainless Steel
Limit Switch box Type ITS520, Inductive Explosion proof, Stainless Steel
Mounting Kits for Limit Switch boxes Type ITS, NAMUR
Limit Switch Inductive sensor Type IFM IN0108
Limit Switch Inductive sensor Type IFM IN0109
Limit Switch Inductive sensor Type IFM IN0110
Limit Switch Inductive sensor Type IFM IN5225
Limit Switch Inductive sensor Type IFM IN5251
Limit Switch Inductive sensor Type IFM IN5285
Limit Switch Inductive sensor Type IFM IN5224
Limit Switch Inductive sensor Type IFM IN5290
Limit Switch Inductive sensor Type IFM NN5008 Eex
Limit Switch Inductive sensor Type IFM NN5009 Eex
Limit Switch Inductive sensor Type IFM NN5013 Eex
Limit Switch Inductive sensor Type IFM IS5001
Limit Switch Inductive sensor Type IFM NS5002 Eex
Target Puck Mounting Kit
Nivå / Flödestrust.
Nivåställ (Digiflow 505 - Microprocessor Controlled Flow Indicator–Integrator)
Nivåställ (Digiflow 505 - Microprocessor Controlled Flow Indicator–Integrator) Image

DIGIFLOW 505 – Microprocessor Controlled Flow Indicator–Integrator * Full scaleable input signals 4 – 20mA analog or frequency. * 2 Inputs either two independent measuring, Dual range, median of two sensors or 2 different channels. * Integration and indicator of totals when time dependent signals. * Simplified Programming. * User Menus in Three Languages. * Control of a Sensor-purge-unit. * Data Logging Output.

Nivåställ (Digiflow 514 - Microprocessor Controlled Flow Indicator–Integrator)
Nivåställ (Digiflow 514 - Microprocessor Controlled Flow Indicator–Integrator) Image

DIGIFLOW 514 – Microprocessor Controlled Flow Indicator–Integrator * Full scalable input signals 4-20m Analog or frequency. * Display of rank total value, preset quantity, flow rate and accumulated quantity. * Two relay outputs for either slow and fast runor two flow channels. * Automatic Overrun compensation. * Alert at signal fault. * Remote Start–Stop. * Simplified programming. * Three languages user interface. * RS 232-protocol interface.

Nivåställ (Digiflow 515 - Microprocessor Gas and Steam Flow Computer)
Nivåställ (Digiflow 515 - Microprocessor Gas and Steam Flow Computer) Image

DIGIFLOW 515 – Microprocessor Gas and Steam Flow Computer * Indication of Flow Rate and Total of Volume, Mass and Energy. * Temperature and Pressure Compensation. * Input Signals 4-20 mA analog or frequency for flow input. * Dual Ranged D.P. Transmitter Inputs. * Simplified Programming. * User Menus in Three Languages. * Control of a Sensor-purge-unit. * Data Logging Output.

Nivåställ (Digiflow 516 - Microprocessor Heat and Energy Flow Computer)
Nivåställ (Digiflow 516 - Microprocessor Heat and Energy Flow Computer) Image

DIGIFLOW 516 – Microprocessor Heat and Energy Flow Computer * Indication of flow rate and total of volume, mass and energy. * Temperature and pressure compensation. * Input signals 4…20 mA analogue or frequency for flow input. * Dual ranged Δp-transmitter inputs. * Simple programming. * User menus in three languages. * Control of a sensor-purge-unit. * Data logging output.

Nivåställ (Digiflow 520 - Microprocessor Controlled Digital Level Indicator)
Nivåställ (Digiflow 520 - Microprocessor Controlled Digital Level Indicator) Image

DIGIFLOW 520 – Microprocessor Controlled Digital Level Indicator * Full scaleable input signals 0/4-20m Analog. * Able to process two input signals as two. * Independent measurements. * Simplified programming. * Indication of the tank content in freely definable. * Units. * Barograph. Indicates the current measured. * Percentage. * Correction for non-linear tanks. * Correction for density changes * User menus in three languages. * German – English – French. * RS232-interface or optional RS485-interface

Nivåställ (Differential Pressure Flow Sensors)
Nivåställ (Differential Pressure Flow Sensors) Image

DIFFERENTIAL PRESSURE FLOW SENSORS – Once an object is brought into a laminar flowing fluid inside a pipe, the fluid will dam up in front of the object, which generates a raise of pressure. Passing the object the fluid gets accelerated due to the smaller pipe cross section. This acceleration generates a pressure drop on the backside of the object. As all operational conditions at the place of measurement are known, the volume of flow can be calculated by using the difference of the two pressures. D.P. flow elements are Itamar-Flow-Sensors.

Nivåställ (Flow Sensor IBF-100, Stack Gas Measurement)
Nivåställ (Flow Sensor IBF-100, Stack Gas Measurement) Image

FLOW SENSOR IBF-100 –  The Itabar flow sensors make it possible to measure the movement of gases, steam and liquids. Special design for stack gas volumetric measurement. The IBF-100 flow sensor was developed especially for stack gas measurements. This flow sensor is engineered to be accessible from both ends so that mechanical cleaning can be undertaken if necessary without having to withdraw the sensor from the sleeve or the stack. This design offers major benefits at pipe diameters of 600 mm (23,62 inch) and more.

Nivåställ (IS210 Clamp-on Ultrasonic Flow Meters)
Nivåställ (IS210 Clamp-on Ultrasonic Flow Meters) Image

CLAMP-ON ULTRASONIC FLOW METERS IS210 – IS210 transit time flow meter utilizes two transducers that function as both ultrasonic transmitters and receivers. The transducers are clamped on the outside of a closed pipe at a specific distance from each other. When the flow meter works, the two transducers transmits and receives ultrasonic signals amplified by multi beam which travels firstly downstream and then upstream. Because ultra sound travels faster downstream than upstream, there will be a difference of time of flight.

Nivåställ (Magnetically Controlled Liquid Level Indicator ITA)
Nivåställ (Magnetically Controlled Liquid Level Indicator ITA) Image

MAGNETICALLY CONTROLLED LIQUID LEVEL INDICATOR ITA – * Indication of the liquid level for corrosive, toxic or flammable media with separation between measurement and display compartments. * Magnetic transmission of the liquid level from the vessel to the gauge is continuous and resistant to vibration. * Can be used to measure level both in atmospheric and pressurized vessels. * Perfect readability of the display elements even at greater distance and after several years, since there is no clouding by product contamination resulting from exposure to ultraviolet light.

Reducerventiler
Reducerventil DRV,508 Dn15-80 (Pressure reducing valve DRV,508 Dn15-80 )
Reducerventil DRV,524 Dn15-80 (Pressure reducing valve DRV,524 Dn15-80 )
Reducerventil DRV,525 Dn15-80 (Pressure reducing valve DRV,525 Dn15-80 )
Reducerventil DRV,550 Dn15-32 (Pressure reducing valve DRV,550 Dn15-32 )
Reducerventil DRV,550 Dn 40-80 (Pressure reducing valve DRV,550 Dn 40-80 )
Reducerventil DRV,578 Dn15-80 (Pressure reducing valve DRV,578 Dn15-80 )
Reducerventil DRV,578SW Dn15-80 (Pressure reducing valve DRV,578SW Dn15-80 )
Reducerventil DRV,602 Dn 80-150 (Pressure reducing valve DRV,602 Dn 80-150 )
Reducerventil DRV,602-6 Dn 80-150 (Pressure reducing valve DRV,602-6 Dn 80-150 )
Reducerventil DRV,608 Dn 80-150 (Pressure reducing valve DRV,608 Dn 80-150 )
Reducerventil DRV,624 Dn 80-150 (Pressure reducing valve DRV,624 Dn 80-150 )
Reducerventil DRV,672 Dn 80-150 (Pressure reducing valve DRV,672 Dn 80-150 )
Reducerventil DRV,678 Dn 80-150 (Pressure reducing valve DRV,678 Dn 80-150 )
Reducerventil DRV,678 HT Dn 80-150 (Pressure reducing valve DRV,678 HT Dn 80-150 )
Reducerventil DRV,678 SW Dn 80-150 (Pressure reducing valve DRV,678 SW Dn 80-150 )
Reducerventil DRV 708 Dn 15-50 (Pressure reducing valve DRV 708 Dn 15-50 )
Reducerventil DRV 724 Dn 15-50 (Pressure reducing valve DRV 724 Dn 15-50 )
Reducerventil DRV 725 Dn 15-50 (Pressure reducing valve DRV 725 Dn 15-50 )
Reducerventil DRV 750 Dn 15-50 (Pressure reducing valve DRV 750 Dn 15-50 )
Reducerventil DRV 772 Dn 15-50 (Pressure reducing valve DRV 772 Dn 15-50 )
Reducerventil DRV 778 Dn 15-50 (Pressure reducing valve DRV 778 Dn 15-50 )
Reducerventil DRV 808 Dn 15-50 (Pressure reducing valve DRV 808 Dn 15-50 )
Reducerventil DRV 824 Dn 15-50 (Pressure reducing valve DRV 824 Dn 15-50 )
Reducerventil DRV 825 Dn 15-50 (Pressure reducing valve DRV 825 Dn 15-50 )
Reducerventil DRV 850 Dn 15-50 (Pressure reducing valve DRV 850 Dn 15-50 )
Reducerventil DRV 878 Dn 15-50 (Pressure reducing valve DRV 878 Dn 15-50 )
Reducerventiler (Pressure Reducing Valve Model 513, 514)
Reducerventiler (Pressure Reducing Valve Model 513, 514) Image

THREAD CONNECTION MODEL 513 –  FLANGA CONNECTION MODEL 514.  – For steam and gases. (For liquids, consult our technical department). Suitable for application in; ironing machines, laundries and dry cleaners’, cooking vats, textile machinery, drying cylinders, autoclaves, steam ovens, distilleries, heat exchangers, the food industry, chemical laboratories, etc.

PRV47 Pilot operated pressure reducing valve DN15-50
Reducerventiler (Diaphragm Sensing, Balanced Valve PRV 30SS)
Reducerventiler (Diaphragm Sensing, Balanced Valve PRV 30SS) Image

DIAPHRAGM SENSING PRESSURE REDUCING VALVE PRV 30SS –  The ADCA PRV30 series direct acting, spring-loaded diaphragm sensing, balanced valve pressure reducing valves, are designed for use on compressed air, water and other gases or liquids compatible with the materials of construction. They are suitable for pressure reducing stations at the point of use on laundry machines, dyeing, food industries, sterilizers, etc.

PRV 25-2S-Carbon steel DN 15-25
PRV 25 I - Stainless steel
Reducerventiler (Pressure Reducing Valve Type AB)
Reducerventiler (Pressure Reducing Valve Type AB) Image

THE AB PRESSURE REDUCING VALVES are balanced inlet design, which are suitable for use on compressed air, gas, water and oil. These valves are used in a variety of applications throughout industry, where their outstanding accuracy and reliability have been proven. The AB is also a WRAS – Approved Product.

Reducerventiler (Pressure Reducing Valves - TYPE B2)
Reducerventiler (Pressure Reducing Valves - TYPE B2) Image

PRESSURE REDUCING VALVES – TYPE B2. – The B2 pressure reducing valves combines high capacity with attendant high accuracy of reduced pressure for steam and gases. These valves are used in a variety of applications throughout industry, where their outstanding accuracy and reliability have been proven. Valves are supplied in sizes half inch to six inch in SG Iron with ends screwed female or alternatively flanged to customers requirements.

Reducerventiler (Pressure Reducing Valves TYPE C3)
Reducerventiler (Pressure Reducing Valves TYPE C3) Image

PRESSURE REDUCING VALVES – TYPE C3. – The C3 pressure reducing valves are direct acting nozzle design, which are suitable for use on compressed air, gas, water, oil and steam. These valves are used in a variety of applications throughout industry, where their outstanding accuracy and reliability have been proven. Valves are supplied in sizes one and half inch to four inch in Gunmetal with ends screwed female or alternatively flanged to customers requirements.

Reducerventiler (Pressure Reducing Valves TYPE C3-L)
Reducerventiler (Pressure Reducing Valves TYPE C3-L) Image

PRESSURE REDUCING VALVES TYPE C3-L – The C3 L pressure reducing valves are balanced inlet design, which are suitable for use on compressed air, gas, water and oil. These valves are ideally suitable for tank blanketing systems, where very low pressures are involved. Valves are supplied in sizes half inch to three inch with ends screwed female or alternatively flanged to customers requirements. The maximum inlet pressure is 10.0 Barg, reduced pressure ranges of 0.015 to 1.0 Barg are possible.

Reducerventiler (Pressure Reducing Valves TYPE C4)
Reducerventiler (Pressure Reducing Valves TYPE C4) Image

PRESSURE REDUCING VALVES TYPE C4 – The C4 High pressure reducing valves are direct acting nozzle design, which are suitable for use on compressed air, gases, water and oil. These valves are used in a variety of applications throughout industry, where their outstanding accuracy and reliability have been proven. Manufactured in Bronze for inlet pressures up to 138 Bar g. For higher inlet pressures, valves are supplied in Carbon Steel or Stainless Steel. The reduced pressure range is from 7 Bar g to 70 Bar g, although higher or lower reduced pressures can be accommodated to suit a particular application.

Reducerventiler (Pressure Reducing Valves TYPE C6)
Reducerventiler (Pressure Reducing Valves TYPE C6) Image

PRESSURE REDUCING VALVES – TYPE C6 – The C6 pressure reducing valves are direct acting nozzle design, which are suitable for use on compressed air, gas, water, oil and steam. These valves are used in a variety of applications throughout industry, where their outstanding accuracy and reliability have been proven. Valves are supplied in sizes quarter inch to one and a quarter inch in Gunmetal with ends screwed female or alternatively flanged to customers requirements. Inlet pressures of up to 250 psig for steam and 300 psig for air and liquid service can be accommodated, although up to 600 psig can be achieved using a reduced orifice and screwed ends.

Reducerventiler (Pressure Reducing Valves TYPE C7/C8)
Reducerventiler (Pressure Reducing Valves TYPE C7/C8) Image

PRESSURE REDUCING VALVES TYPE C7/C8 – The C7/C8 pressure reducing valves are direct acting nozzle design, which are suitable for use on compressed air, gas, water, oil and steam. These valves are used in a variety of applications throughout industry, where their outstanding accuracy and reliability have been proven. Valves are supplied in sizes one inch to two inch with ends screwed female or alternatively flanged to customers requirements. The maximum inlet pressure is 40.0 Barg, reduced pressure ranges of 0.35 to 10.0 Barg are possible.

Reducerventiler (Pressure Reducing Valves TYPE C9)
Reducerventiler (Pressure Reducing Valves TYPE C9) Image

PRESSURE REDUCING VALVES TYPE C9 – The C9 pressure reducing valves are direct acting nozzle design, which are suitable for use on compressed air, gas, water, oil and steam. These valves are used in a variety of applications throughout industry, where their outstanding accuracy and reliability have been proven. Valves are supplied in sizes half inch to four inch with ends screwed female or alternatively flanged to customers requirements. The maximum inlet pressure is 82.0 Barg, reduced pressure ranges of 1.70 to 21.0 Barg are possible.

reducing valve T7 without auxiliary power, for steam
reducing valve T7 without auxiliary power, for steam Image

Pressure reducing valve T7
without auxiliary power, for steam
PN40 – DN15-200 PN100 – DN15-40

reducing valve T9 without auxiliary power, for liquids and gases
reducing valve T9 without auxiliary power, for liquids and gases Image

Pressure reducing valve T9
without auxiliary power, for liquids and gases
PN40 – DN15-200 PN100 – DN15-40

Sprängbleck
Sprängbleck/Sprängpaneler (SCD Rupture Disc)
Sprängbleck/Sprängpaneler (SCD Rupture Disc) Image

The SCD RUPTURE DISC is a concave rupture with micro-scored calibrated section. Special feature of SCD is scoring in 6 sectors instead of 4 as usual in all competitors’ discs. Opening in 6 petals allows a better opening reducing the risk of petal detachment even at high bursting pressure. It is used with gas and liquids also in cycling and pulsating conditions without reduction of safety margins. SCD disc reacts to excessive pressure in a few milliseconds without fragmentation. It is especially suited for protection of pressure relief valves

Sprängbleck/Sprängpaneler (DCD Rupture Disc)
Sprängbleck/Sprängpaneler (DCD Rupture Disc) Image

The DCD RUPTURE DISC is a composite conventional disc formed by three parts: A slotted, perforated metal part, A seal membrane (usually in PTFE but also available in many other metallic or non-metallic materials, A protection section. It is excellent for use with gas and liquids in static conditions and excellent for low pressures. DCD disc is particularly suitable to be fitted on equipment and systems. It reacts to over-pressure in a few thousands of a second with total opening and without fragmentation. DCD disc is therefore recommended for protection of pressure relief valves.

Sprängbleck/Sprängpaneler (Y90 Rupture Disc)
Sprängbleck/Sprängpaneler (Y90 Rupture Disc) Image

The Y90 RUPTURE DISC is a compression (or reverse) disc peripherally scored. The Y90 represents high technology in the sector: the camber of the convex disc is not modified by the operating pressure except on reaching reverse pressure. Therefore this device works with ratios of up to 90% between operating and rupture pressure and withstands thousands of cycles without jeopardising its reliability.

Sprängbleck/Sprängpaneler (STD Rupture Disc)
Sprängbleck/Sprängpaneler (STD Rupture Disc) Image

The STD RUPTURE DISC is a conventional concave disc with solid calibrated section. It is a simple and reliable device used with gas and liquids in cyclic and pulsating conditions. STD discs react to excessive pressure in a few thousands of second. Supports for vacuum and counter-pressure are available

Sprängbleck/Sprängpaneler (DIF Rupture Disc)
Sprängbleck/Sprängpaneler (DIF Rupture Disc) Image

The DIF RUPTURE DISC is a composite conventional disc formed by four parts: A slotted, perforated metal part, A seal membrane (usually in PTFE but also available in many other metallic or non- metallic materials, A protection section, A calibration ring. This disc has been designed to be mounted between flanges. It is excellent for use with gas and liquids in static conditions and excellent for low pressures. DIF disc is particularly suitable to be fitted on equipment and systems. It reacts to over-pressure in a few thousands of a second with total opening and without fragmentation.

Sprängbleck/Sprängpaneler (LDP Rupture Disc)
Sprängbleck/Sprängpaneler (LDP Rupture Disc) Image

The LPD RUPTURE DISC is a composite conventional disc formed by four parts: A slotted, perforated metal part. A seal membrane (usually in PTFE). A protection section. A calibration ring with blades to improve membrane opening. Designed to protect processing and storage tanks, atmospheric vessels and silos against implosion or overpressure conditions. It reacts to over-pressure in a few thousands of a second with total opening and without fragmentation. LPD discs are a simple, reliable, accurate and economical solution for applications requiring extremely low positive and/or negative pressure protection.

Sprängbleck/Sprängpaneler (TCD Rupture Disc)
Sprängbleck/Sprängpaneler (TCD Rupture Disc) Image

The TCD RUPTURE DISC is a composite conventional disc formed by four parts: A slotted, perforated metal part. A seal membrane (usually in PTFE but also available in many other metallic or non- metallic materials. A protection section. A calibration ring. This disc has been designed specifically to be mounted on rail or road tankers transporting liquids or gases in static or pulsating conditions. It reacts to over-pressure in a few thousands of a second with total opening and without fragmentation. TCD disc is therefore recommended for protection of pressure relief valves.

Sprängbleck/Sprängpaneler (GM Rupture Disc)
Sprängbleck/Sprängpaneler (GM Rupture Disc) Image

The GM RUPTURE DISC of monoblock graphite is versatile and suitable for numerous applications. It may be directly inserted between flanges. Graphite discs are very resistant to aggressive fluids, even at high temperature. Bursting pressure has low sensitivity to temperature variations. GM disc is made of high purity graphite impregnated with phenolic resins in order to make the product non-porous opening is total but with fragmentation.

Sprängbleck/Sprängpaneler (GR Rupture Disc)
Sprängbleck/Sprängpaneler (GR Rupture Disc) Image

The replaceable “GR” graphite rupture disc is mounted on a graphite or metal holder. This disc is versatile and suitable for numerous applications. It is available in metric measurements and in inches and can be inserted between relative flanges. Graphite discs are very resistant to aggressive fluids, even at high temperature. Bursting pressure has low sensitivity to temperature variations.

Sprängbleck/Sprängpaneler (GA Rupture Disc)
Sprängbleck/Sprängpaneler (GA Rupture Disc) Image

The replaceable GA graphite RUPTURE DISC is mounted on a Stainless steel (or other metal) ring and may be directly inserted between flanges. This disc is very versatile because has both the robustness of a metal holder and the performance of a graphite disc (very resistant to aggressive fluids, even at high temperature, low sensitivity of bursting pressure to temperature variations).

Sprängbleck/Sprängpaneler (Holders)
Sprängbleck/Sprängpaneler (Holders) Image

The HOLDERS are designed in order to ensure maximum performance and reliability to the rupture discs. Models designed to be mounted between flanges (HI, Y90 e GR) have an internal diameter sized in order to allow full opening of the disc and total availability of the minimal discharge area; external diameter is tangent to the bolts in order to center easily the holder between the flanges

Sprängbleck/Sprängpaneler (Pressure Supports)
Sprängbleck/Sprängpaneler (Pressure Supports) Image

VACUUM COUNTER PRESSURE SUPPORTS – When the rupture disc may be subjected to conditions of vacuum or counter-pressure a support of adequate design and resistance may be required. The selection of support type is guided by disc type and operation conditions Vacuum / counter-pressure supports supplied. The SDD are of 5 types: * Flat grid, * Convex grid, * Finned, * Slotted in sectors, * Slotted along the circumference.

Sprängbleck/Sprängpaneler (Explosion Vent Panels)
Sprängbleck/Sprängpaneler (Explosion Vent Panels) Image

EXPLOSION VENT PANELS – The PS/R (rectangular) and PS/C (circular) explosion vent panels are composite tension panels composed of three parts: * A slotted, perforated metal part, * A seal membrane (usually in PTFE),  * A protection section. In addition vacuum support is available. Suitable for use with gas in static, pulsating and cyclic conditions. PS explosion vent panels are available in square, rectangular or circular models. They usually have very low vent or vacuum pressures.

Sprängbleck/Sprängpaneler (SVT/AT Rupture Indicator)
Sprängbleck/Sprängpaneler (SVT/AT Rupture Indicator) Image

RUPTURE INDICATOR – The SVT/AT alarm system is a simple and efficient instrument for recording the bursting of a rupture disc. The detector is installed between the container on the discharge side and the flange down stream from the safety device replacing the traditional seal. The cables of the alarm system must be connected to the plant’s safety system with an intrinsically safe barrier adequate to the sensor (max tension 24 AC/DC and max current 150 mA) and the hazardous area classification.

Sprängbleck/Sprängpaneler (IRP Rupture Indicator)
Sprängbleck/Sprängpaneler (IRP Rupture Indicator) Image

RUPTURE INDICATOR – The IRP alarm system is a simple and efficient instrument for recording the bursting of an explosion venting panel. The detector is installed during manufacturing of the explosion venting panel and has a 2m shielded cable. The cables of the alarm system must be connected to the plant’s safety system with an intrinsically safe barrier adequate to the sensor (max tension 24 AC/DC and max current 150 mA) and the hazardous area classification.

Sprängbleck/Sprängpaneler (NAM 03/HT Magnetic Alarm)
Sprängbleck/Sprängpaneler (NAM 03/HT Magnetic Alarm) Image

NAM 03/HT alarm system is recommended for installation with SDD rupture discs. NAM 03/HT Alarm System is made up of: * A proximity type sensor installed in the disc holder downstream the disc in order to detect the bursting of the disc. * A target with a permanent magnet supplied with the disc. When the disc bursts the magnet is displaced and the sensor activated. Replacement discs are supplied with a new target.

Sprängbleck/Sprängpaneler (NAM 05 Inductive Alarm)
Sprängbleck/Sprängpaneler (NAM 05 Inductive Alarm) Image

INDUCTIVE ALARM SYSTEM – NAM 05 alarm system is recommended for installation on Rupture discs and explosion vent panels. NAM 05 Alarm System is made up of: * An inductive proximity sensor installed downstream the disc or panel. * A target supplied with the disc or panel. When the disc or panel opens the target is moved and the sensor sends a signal to the plant safety system. Spare discs or panels are supplied with a new actuator.

Säkerhetsventiler
Säkerhetsventiler (Safety Valve 341- Spring Loaded Diaphragm)
Säkerhetsventiler (Safety Valve 341- Spring Loaded Diaphragm) Image

SAFETY VALVE SPRING LOADED HIGH-EFFICIENCY DIAPHRAGM TYPE – Safety valve to satisfy safety requirements in heating systems with flow temperatures of 120°C according to DIN 4751 Pt. 2. Spring loaded, diaphragm type, high-efficiency safety valve, angled, with highly elastic seal and metal backing in the valve head. Series 341 with closed bonnet Valve head is liftable. The pressure acts, via a ball, centrally onto the valve head. Corrosion-resistant spindle bushes ensure reliable and precise response of the valve.

 

 

Säkerhetsventiler (Safety Valve 356 - Spring Loaded, Gas-Tight)
Säkerhetsventiler (Safety Valve 356 - Spring Loaded, Gas-Tight) Image

SAFETY VALVES – SPRING LOADED HIGH-EFFICIENCY – As safety valves for steam, gases and hot water in pressure vessels and steam boilers with closed protective bonnet and gas-tight lift housing.

 

Säkerhetsventiler (Safety Valve 357 - Spring Loaded, Closed Bonnet)
Säkerhetsventiler (Safety Valve 357 - Spring Loaded, Closed Bonnet) Image

SAFETY VALVES – SPRING LOADED HIGH-EFFICIENCY – Application: As safety valves for steam, gases and hot water in pressure vessels and steam boilers. Series 357 version with closed bonnet Liftable valve head. Force is transmitted centrally at the valve head via ball. Corrosion-resistant spindle guides ensure reliable and precise response of the valve.

Säkerhetsventiler (Safety Valve 360 - Spring Loaded, Gas-Tight)
Säkerhetsventiler (Safety Valve 360 - Spring Loaded, Gas-Tight) Image

SAFETY VALVES – SPRING LOADED HIGH-EFFICIENCY – Series 360, Gas-tight with closed protective bonnet and closed lift housing. Safety valves for blowing-off liquid from fixed pressure vessels, subject to the condition that no evaporation occurs. Also suited to district heating systems. If the liquid to be blown off does not have similar properties to the liquid (water) used in the valve testing procedure, then the properties of the liquid, in respect to chemical aggressiveness or sticking tendency, must be taken into account in the acceptance testing of the pressure vessel.

Säkerhetsventiler (Safety Valve 361 - Spring Loaded, Closed Bonnet)
Säkerhetsventiler (Safety Valve 361 - Spring Loaded, Closed Bonnet) Image

SAFETY VALVES – SPRING LOADED HIGH-EFFICIENCY –  Series 361 with closed protective bonnet and open lift housing. Valve head is liftable. Force is transmitted centrally at the valve head. Corrosion-resistant spindle guides ensure reliable and precise response of the valve. Safety valves for blowing-off liquid from fixed pressure vessels, subject to the condition that no evaporation occurs. Also suited to district heating systems.

Säkerhetsventiler (Safety Valve 390 - Diaphragm, Closed Bonnet)
Säkerhetsventiler (Safety Valve 390 - Diaphragm, Closed Bonnet) Image

SAFETY VALVES – DIAPHRAGM HIGH-EFFICIENCY – 390 with closed bonnet, response overpressure: 0,5 bar. Nom. diam. 25 to 100. Liftable valve head. Force is transmitted centrally at the valve head via ball. Corrosion-resistant spindle guides ensure reliable and precise response of valve. These safety valves are for blowing-off saturated steam from pressure generators.

Säkerhetsventiler (Safety Valve 391 - Diaphragm, Closed Bonnet)
Säkerhetsventiler (Safety Valve 391 - Diaphragm, Closed Bonnet) Image

SAFETY VALVES – DIAPHRAGM HIGH-EFFICIENCY – 391 with closed bonnet, response overpressure: 0,5 bar, nom. diam. 125 to 150. Weight loaded, diaphragm type, high-efficiency safety valve, angled, with highly elastic seal and metal backing in valve head. Liftable valve head. Force is transmitted centrally at the valve head via ball. Corrosion-resistant spindle guides ensure reliable and precise response of valve. These safety valves are for blowing-off saturated steam from pressure generators.

Säkerhetsventiler (Safety Valve 392 - Diaphragm, Closed Bonnet)
Säkerhetsventiler (Safety Valve 392 - Diaphragm, Closed Bonnet) Image

SAFETY VALVES – DIAPHRAGM HIGH-EFFICIENCY – 392 with closed bonnet, response overpressure: 1 bar, nom. diam. 25 to 50. Weight loaded, diaphragm type, high-efficiency safety valve, angled, with highly elastic seal and metal backing in valve head. Liftable valve head. Force is transmitted centrally at the valve head via ball. Corrosion-resistant spindle guides ensure reliable and precise response of valve. These safety valves are for blowing-off saturated steam from pressure generators.

Säkerhetsventiler (Safety Valve 393 - Diaphragm, Closed Bonnet)
Säkerhetsventiler (Safety Valve 393 - Diaphragm, Closed Bonnet) Image

SAFETY VALVES – DIAPHRAGM HIGH-EFFICIENCY – 393 with closed bonnet, response overpressure: 1 bar, nom. diam. 25 to 100, nom. diam. 125 to 150. Spring loaded, diaphragm type, high-efficiency safety valve, angled, with highly elastic seal and metal backing in valve head. Liftable valve head. Force is transmitted centrally at the valve head via ball. Corrosion-resistant spindle guides ensure reliable and precise response of valve.

Safety overflow valve T27 without auxiliary power, for liquids and gas
Safety overflow valve T27 without auxiliary power, for liquids and gas Image

Safety overflow valve T27
without auxiliary power, for liquids and gas
PN40 – DN15-200 PN100 – DN15-40

Safety overflow valve T27 F without auxiliary power, for liquids and gas
Safety overflow valve T27 F without auxiliary power, for liquids and gas Image

Safety overflow valve T27 F
without auxiliary power, for liquids and gas
PN40 – DN15-200 PN100 – DN15-40

TYPE 494 Normal safety valve (AN)
TYPE 495 Full lift safety valve with spring loading (AIT)
TYPE 496 Full lift safety valve with spring loading (AIT)
TYPE 295 Normal safety valve with spring loading (AN)
Säkerhetsventiler (Safety valve with spring loading Model 095)
Säkerhetsventiler (Safety valve with spring loading Model 095) Image

SAFETY VALVE WITH SPRING LOADING MODEL 095 – The valve works as an automatic pressure releasing regulator activated by the static pressure existing at the entrance to the valve and is characterized by its ability to open proportional to the pressure increase. Design in accordance with “International Standard ISO 4126-1:2004 Safety Valves”. In accordance with the requirements of directive 97/23/EC. EC valve verification certified by: TÜV Internacional Grupo TÜV Rheinland, S.L. EC 0035.

Säkerhetsventiler (Safety valve with spring loading Model 096)
Säkerhetsventiler (Safety valve with spring loading Model 096) Image

SAFETY VALVE WITH SPRING LOADING MODEL 096 – The valve works as an automatic pressure releasing regulator activated by the static pressure existing at the entrance to the valve and is characterized by its ability to open proportional to the pressure increase. Design in accordance with “International Standard ISO 4126-1:2004 Safety Valves”. In accordance with the requirements of directive 97/23/EC. EC valve verification certified by: TÜV Internacional Grupo TÜV Rheinland, S.L. EC 0035.

TYPE 694,995,695 Full lift safety valve with spring loading. (AIT)
Vridspjällventiler
Vridspjällventil 700G Wafer (Butterfly Valve 700G Wafer)
Vridspjällventil 700G Wafer (Butterfly Valve 700G Wafer) Image

BUTTERFLY VALVE  700G Wafer – Low pressure applications including, sand, cement powder, sea water, waste water, sugar processing, general food industry, fertiliser spraying, carbon black, low vacuum and compressed air. Valve Nominal Size: 40mm to 200mm, 250mm to 300mm, 350mm to 500mm and 600mm.

Vridspjällventil 704G Full lugged (Butterfly Valve 704G Full lugged)
Vridspjällventil 704G Full lugged (Butterfly Valve 704G Full lugged) Image

BUTTERFLY VALVE 704G full lugged  – For low pressure applications including, sand, cement powder, sea water, waste water, sugar processing, general food industry, fertiliser spraying, carbon black, low vacuum and compressed air. Valve Nominal Size: 50mm to 200mm, 250mm to 300mm, 350mm to 500mm and 600mm.

Vridspjällventil 705G Semi Lugged (Butterfly Valve 705G Semi Lugged )
Vridspjällventil 705G Semi Lugged (Butterfly Valve 705G Semi Lugged ) Image

BUTTERFLY VALVE  705G Semi lugged – For low pressure applications including, sand, cement powder, sea water, waste water, sugar processing, general food industry, fertiliser spraying, carbon black, low vacuum and compressed air. Valve Nominal Size: 50mm to 200mm, 250mm to 300mm, 350mm to 500mm and 600mm.

Vridspjällventil 773Z,700Z (Butterfly Valve 773Z,700Z)
Vridspjällventil 773Z,700Z (Butterfly Valve 773Z,700Z) Image

This lightweight, cost effective butterfly valve is ideally suited for applications up to 10 Barg. The superior leaktight properties are achieved by using the proven 16 Barg rated 700G disc and seat within a lightweight body. The 773Z valve conforms to ISO5752 face-to-face dimensions and ISO5211 actuator mounting flange.

Vridspjällventil 731P,732P Wafer (Butterfly Valve 731P,732P Wafer)
Vridspjällventil 731P,732P Wafer (Butterfly Valve 731P,732P Wafer) Image

A wafer or lugged pattern, rubber seated butterfly valve. The seat is vulcanised to the valve body, and incorporates a modified cosine curve seat profile. This provides lower torque, reduced friction and improved flow characteristics, especially at the partially open position.
The vulcanised seat also ensures improved performance under high velocity and vacuum conditions.

Vridspjällventil 732Q,752W Lugged (Butterfly Valve 732Q,752W Lugged)
Vridspjällventil 732Q,752W Lugged (Butterfly Valve 732Q,752W Lugged) Image

A wafer or lugged pattern, rubber seated butterfly valve. The seat is vulcanised to the valve body, and incorporates a modified cosine curve seat profile. This provides lower torque, reduced friction and improved flow characteristics, especially at the partially open position. The vulcanised seat also ensures improved performance under high velocity and vacuum conditions.

Vridspjällventil 700E,K,S (Butterfly Valve 700E,K,S)
Vridspjällventil 700E,K,S (Butterfly Valve 700E,K,S) Image

Large diameter rubber seated butterfly valves, wafer with support lugs, for general and marine duties.
Size Range:DN650 – DN1350 (26″ – 54″)
Pressure Rating:10 bar
Body Patterns:Wafer with support lugs
Body Seat:EPDM, NBR
Body Materials:Ductile Iron, Cast Iron, Carbon Steel
Disc Materials:Ductile Iron, Alu Bronze
Temperature Rating:-20°C to +120°C
Flange Standards:ANSI150, PN10, JIS 5K/10K
Operation:Manual, Electric, Pneumatic

Vridspjällventil 720F/722F (Butterfly Valve 720F/722F)
Vridspjällventil 720F/722F (Butterfly Valve 720F/722F) Image

Large diameter rubber seated butterfly valves, lugged & double flanged,for general and marine duties.
Size Range: DN50 – DN1350 (2″ – 54″)
Pressure Rating: 10 bar
Body Patterns: Wafer, Flanged
Body Seat: EPDM, NBR
Body Materials: Cast Steel
Disc Materials: 304 & 316 St.Steel
Temperature Rating: -20°C to +120°C

Vridspjällventil 71LG (Butterfly Valve 71LG)
Vridspjällventil 71LG (Butterfly Valve 71LG) Image

The 71LG provides 16 BARg fully rated lugged pattern valves up to DN600 (24″) The renowned TOMOE cosine seat design ensures reliable and consistent sealing at a fully rated 16 BARg pressure application. Multi layered stem bearings and unique disc design ensures reliable sealing and less torque. Higher Cv values and pressure loss figures at the fully open position are significantly lower than those of competitors. Field replaceable seat ring makes maintenance easy and reduces maintenance costs.

Vridspjällventil KRV (Butterfly Valve KRV)
Vridspjällventil KRV (Butterfly Valve KRV) Image

A large diameter Double Flanged butterfly valve with a Lightweight, slim disc design provides high Cv values and low pressure loss figures at the fully open position. Concentric butterfly valve design makes it suitable for bi-directional flow and multi layered stem bearings ensure optimum torque figures are delivered and maintained. Replaceable seat ring makes maintenance easy and reduces costs.
Size Range:DN1000 – DN2000 (40″ – 80″)
Pressure Rating:6 bar
Body Patterns:Double flanged
Body Seat:EPDM, NBR
Body Materials:Carbon Steel, WCB
Disc Materials:Carbon Steel, 316 St.Steel

Vridspjällventil 227P (Butterfly Valve 227P)
Vridspjällventil 227P (Butterfly Valve 227P) Image

Large diameter rubber seated butterfly valves, AWWA C504 standard, double flanged, for general duties without AWWA approval.
Size Range: DN650 – DN2400 (26″ – 96″)
Pressure Rating: 16 bar
Body Patterns: Double flanged
Body Seat: EPDM, NBR
Body Materials: Carbon Steel
Disc Materials: St.Steel, Alu Bronze
Temperature Rating: -10°C to +80°C 

Vridspjällventil 841T,842T PTFE (Butterfly Valve 841T,842T PTFE)
Vridspjällventil 841T,842T PTFE (Butterfly Valve 841T,842T PTFE) Image

841T / 842T PTFE Lined for chemical duties with a proven record of excellent performance and long life in heavy duty applications.

Vridspjällventil 846T,847T PFA (Butterfly Valve 846T,847T PFA)
Vridspjällventil 846T,847T PFA (Butterfly Valve 846T,847T PFA) Image

Fully PFA lined butterfly valve with either stainless steel encapsulated, or PPS disc.
A chemically resistant butterfly valve. Design features of the 846T,847T result in low torque, superior strength and sealing properties, essential in applications where conditions are potentially hazardous. Size: 50mm to 200mm or 250mm to 300mm. Working Temperature Range: Intermittent = -20 to +200 C, Continuous = 0 to +150 C.

Vridspjällventil 302A,303Q Firesafe (Butterfly Valve302A,303Q Firesafe)
Vridspjällventil 302A,303Q Firesafe (Butterfly Valve302A,303Q Firesafe) Image

Double Offset, metal seated Fire-safe valves to API standards. The range is certified Fire-safe to API 607 4th edition, and is available in both wafer and lugged pattern bodies.
This high performance butterfly valve is suitable for bi-directional flow, and the disc is designed to reduce thermal expansion, thus providing constant sealing performance against temperature and pressure cycling conditions.

Vridspjällventiler 302Y metallsäte (Butterfly Valve302Y Metal Seat)
Vridspjällventiler 302Y metallsäte (Butterfly Valve302Y Metal Seat) Image

Designed for operation in high pressure/high temperature environments, the 302Y high performance butterfly valve features several unique features which combine precision engineering with advanced design (eg self-aligning, high rigid thin-wall disc and “ball lock” seat retainer) to produce the ideal replacement for conventional metal seating gate and globe valves. Size: 40mm to 150mm, 200mm and 250mm to 300mm. Working Temperature Ranges: -20 C to +250 C.

Vridspjällventil 304 A,Q (API Spec) (Butterfly Valve304 A,Q (API Spec)
Vridspjällventil 304 A,Q (API Spec) (Butterfly Valve304 A,Q (API Spec) Image

This valve is a double offset high performance butterfly valve identical to the 304Y valve range, but built to API standards.
Size Range:DN80 – DN600 (3″ – 24″)
Pressure Rating:20 bar
Body Patterns:Wafer, Lugged
Body Seat:RPTFE
Body Materials:WCB, 304SS, 316SS
Disc Materials:304SS
Temperature Rating:-20°C to +200°C

Vridspjällventiler 304Y RPTFEsäte (Butterfly Valve 304Y RPTFE Seat)
Vridspjällventiler 304Y RPTFEsäte (Butterfly Valve 304Y RPTFE Seat) Image

The 304Y high performance butterfly valve has a distinctive “J” shaped PTFE seat ring which does not detract from the rigidity of the valve mechanism, yet provides a more user friendly torque profile – but without sacrificing durability or leak tightness. In common with its stable companion, the 302Y, this valve complies with face-to-face ISO5752 and ISO5211 mounting flange requirements. Nominal Size: 40mm to 150mm, 200mm and 250mm to 300mm. Working Temperature Ranges: -20 C to +200 C.

Vridspjällventil 334 Class 300 (Butterfly Valve334 Class 300)
Vridspjällventil 334 Class 300 (Butterfly Valve334 Class 300) Image

Double Offset PTFE Seated High Performance Butterfly Valve to Suit API Standard. Fire Safe Certication As Optional. Class 300.
Size Range:DN80 – DN600 (3″ – 24″)
Pressure Rating:51 bar
Body Patterns:Wafer, Lugged, DFSP
Body Seat:RPTFE+316 retainer
Body Materials:WCB, 316SS, Alu Bronze
Disc Materials:316SS
Temperature Rating:-29°C to +232°C
Certification:API607 4th
Flange Standards:
ANSI150/300, PN25/40, JIS 10K/16K/20K

Reglerventil 507V Metallsäte (Control Valve 507V Metal Seat)
Reglerventil 507V Metallsäte (Control Valve 507V Metal Seat) Image

Rotary Control Valve for high temperature fluids up to 400°C.Designed exclusively for the regulation of fluids, the 507V Control Butterfly Valve range provides:
High rangeability Reduced dynamic torque
Low noise levels. Anti-cavitation Wide temperature range.
Size Range:DN50 – DN400 (2″ – 16″)
Pressure Rating:Class 150, Class 300
Body Patterns: Wafer Body Seat:None
Body Materials:WCB, 316SS
Disc Materials: WCB, 316SS
Temperature Rating: -50°C to +400°C

Reglerventil 508V EPDM, NBR (Control Valve 508V EPDM, NBR )
Reglerventil 508V EPDM, NBR (Control Valve 508V EPDM, NBR ) Image

Rotary Control Valve with tight shut-off and high grade rubber seat ring. The 508V ensures tight shut-off and eliminates the need for any additional stop valve that is normally required by conventional control valves.
Size Range: DN50 – DN600 (2″ – 24″)
Pressure Rating: 10 bar
Body Patterns: Wafer Body Seat:EPDM, NBR
Body Materials: Carbon Steel
Disc Materials:304SS, 316SS
Temperature Rating: -20°C to +120°C

Vridspjällventiler Double Block & Bleed
Vridspjäll Block Bleed (DBB1 Triple Offset Butterfly Valve)
Vridspjäll Block Bleed (DBB1 Triple Offset Butterfly Valve) Image

The Twin seat block & bleed valves provide the benefits Of the Triple Offset design with none of the disadvantages (space, weight, cost) associated with Gate or Ball valve designs.
Size Range: DN50 – DN1200 (2″ – 48″)
Pressure Rating: Class 150 – Class 2500
Body Patterns: Wafer, Lugged, DFSP, DFLP, BWE, Hub, etc
Body Seat: 316SS, Graphite
Body Materials: WCB, 304, 316, Hastalloy, Inconel, etc.
Disc Materials: WCB, 304, 316, Hastalloy, Inconel, etc.
Temperature Rating: -46°C to +750°C
Certification: API607
Operation: Manual, Electric, Pneumatic, Hydraulic.

Vridspjäll Block Bleed (DBB2 Triple Offset Butterfly Valve)
Vridspjäll Block Bleed (DBB2 Triple Offset Butterfly Valve) Image

The Double Isolation and bleed facility valve DFSP, provide the benefits Of the Triple Offset design with none of the disadvantages (space, weight, cost) associated with Gate or Ball valve designs.
Size Range: DN50 – DN1200 (2″ – 48″)
Pressure Rating: Class 150 – Class 2500
Body Patterns: Wafer, Lugged, DFSP, DFLP, BWE, Hub, etc
Body Seat: 316SS, Graphite
Body Materials: WCB, 304, 316, Hastalloy, Inconel, etc.
Disc Materials: WCB, 304, 316, Hastalloy, Inconel, etc.
Temperature Rating:-46°C to +750°C
Certification: API607
Operation: Manual, Electric, Pneumatic, Hydraulic.

Vridspjäll Block Bleed (DBB3 Triple Offset Butterfly Valve)
Vridspjäll Block Bleed (DBB3 Triple Offset Butterfly Valve) Image

The Double Isolation and bleed facility valves , with two lugged valve bodies with central spool piece provide the benefits Of the Triple Offset design with none of the disadvantages (space, weight, cost) associated with Gate or Ball valve designs.
Size Range: DN80 – DN1200 (3″ – 48″)
Pressure Rating: Class 150 – Class 2500
Body Patterns: Wafer, Lugged, DFSP, DFLP, BWE, Hub, etc
Body Seat: 316SS, Graphite
Body Materials: WCB, 304, 316, Hastalloy, Inconel, etc.
Disc Materials: WCB, 304, 316, Hastalloy, Inconel, etc.
Temperature Rating: -46°C to +750°C
Certification: API607
Operation: Manual, Electric, Pneumatic, Hydraulic.

Vridspjäll Tritec (TT1 Triple Offset Butterfly Valve)
Vridspjäll Tritec (TT1 Triple Offset Butterfly Valve) Image

In comparison to conventional valves, butterfly valves are smaller and lighter, making them ideal for space conscious plant designs, particularly FPSO’s and offshore rigs. However, a standard butterfly valve does not have the control or shut off requirements for high pressure, high temperature applications. The Triple Offset design moves the centre of rotation within the valve and utilises an ellipsoidal sealing geometry. This allows a wide range of metal seating materials to be used, providing zero leakage performance on high temperature, high pressure and firesafe applications.
Size Range: DN50 – DN1650 (2″ – 66″)
Pressure Rating: Class 150-Class 2500
Body Patterns:Wafe,Lugged,DFSP,DFLP, BWE, Hub, etc
Body Seat: 316SS, Graphite
Body Materials:WCB,304,316,Hastalloy, Inconel, etc.
Disc Materials:WCB,304,316,Hastalloy, Inconel, etc.
Temperature Rating:-46°C to +750°C
Certification:API6FA, API607
Operation:Manual, Electric,Pneumatic, Hydraulic.

Vridspjäll Triple Offset (TT2 Triple Offset Butterfly Valve)
Vridspjäll Triple Offset (TT2 Triple Offset Butterfly Valve) Image

Triple Offset butterfly valve available in Wafer, Lugged and Double Flanged body styles to 150 lb and 300 lb pressure ratings, the TT2 triple offset valve has fire safe certification to API607 5th Edition.
Size Range: DN80 – DN600 (3″ – 24″)
Pressure Rating: Class 150, Class 300
Body Patterns: Wafer,Lugged,DFSP,DFLP
Body Seat: 316SS, Graphite
Body Materials: WCB, 316SS
Disc Materials: WCB, 316SS
Temperature Rating: -29°C to +600°C
Certification: API607
Operation: Manual,Electric,Pneumatic, Hydraulic.

Ång och kondensatutrustning
DT40S Thermodynamic steam trap DN10-25
DT42S Thermodynamic steam traps DN15-25
DT32 Thermodynamic steam traps DN15-25
CDV32 Condensate drain valve DN15-20
TH13A Thermostatic steam trap & air vent DN15
TH21 Thermostatic steam trap DN15
TH21SS Thermostatic steam trap DN15-25
TH32Y Thermostatic steam trap DN15-25
TSS22 Thermostatic steam trap DN08-25
TSW22 Wafer thermostatic steam trap DN 15-25
TH35-2-3 Thermostatic steam trap DN25
IB12 Inverted bucket steam traps DN15-20
IBB12 Inverted bucket steam traps DN20-25
IB30S-IB30SS Inverted bucket steam traps DN15-25
IB35S-IB35SS Inverted bucket steam traps DN15-25
FLT17-LC Float and thermostatic steam traps DN15-20
FLT17 Float and thermostatic steam traps DN15-25
FLT17 Float and thermostatic steam traps DN40-50
FLT17 Float and thermostatic steam traps DN50HC
FLT32 Float and thermostatic steam traps DN15-25
FLT32 Float and thermostatic steam traps DN25HC
FLT32 Float and thermostatic steam traps DN40-50
FLT14I Float and thermostatic steam traps DN15-20
FLT14I Float and thermostatic steam traps DN25
FLT14I Float and thermostatic steam traps DN25HC
FLT14I Float and thermostatic steam traps DN40-50
FLT Float & thermostatic steam trap with SLR Assembly
FLT22S-FLT22SS Float and thermostatic steam traps DN40-50
FLT22G-TW Twin float and thermostatic steam traps DN80-100
FLT22S-FLT22SSTW Twin float and thermostatic steam traps DN80-100
FLT120 Float and orifice steam trap DN150
FLT150-TW Float and thermostatic steam traps DN100-150
BSS20 Bimetallic steam trap DN 15
BS32 Bimetallic steam trap DN15-20
BM20 Bimetallic steam trap DN15-25
BM20SS Bimetallic steam trap DN15-25
BM20R Bimetallic temperature control steam trap DN15-25.
BM24 Bimetallic steam trap DN15-25
BM24 Bimetallic steam traps DN40-50
BM32 Bimetallic steam trap DN15-25
BM32 Bimetallic steam trap DN40-50
BM35 Bimetallic steam trap DN 15-25
BM45 Bimetallic steam trap DN 15-25
BM80 Bimetallic steam trap DN 15-25
BM140 Bimetallic steam trap DN 15-25
BM-HC Bimetallic steam trap DN 40-100
TH32YCK Thermostatic steam trap DN15-25
Elektriska ställdon
Elektriska Manöverdon (Electrical Actuator type ITQ 002)
Elektriska Manöverdon (Electrical Actuator type ITQ 002) Image

ELECTRICAL ACTUATOR TYPE ITQ 002 –  * ON/OFF automation of small ball valves etc. * Standard supply voltage 1 phase 230V, optional voltage available. * Very compact and light weight. * Power option: other voltages

Elektriska Manöverdon (Electrical Actuator type ITQ 004)
Elektriska Manöverdon (Electrical Actuator type ITQ 004) Image

ELECTRICAL ACTUATOR TYPE ITQ 004 – * ON/OFF automation of small ball valves and dampers. * Special designed induction motor. * High starting torques and thermally protected from overheating. * Compact and light weight. * Standard supply voltage 1 phase 230V, optional voltage available

Elektriska Manöverdon (Electrical Actuator type ITQ 008)
Elektriska Manöverdon (Electrical Actuator type ITQ 008) Image

ELECTRICAL ACTUATOR TYPE ITQ 008 –  * ON/OFF automation of small ball valve, plug valves and dampers. * Self locking combination of spur and worm gears. * Special designed induction motor that produces high starting torques and thermally protected from overheating. * External mechanical stopper bolts. * Manual operation by wrench directly to the gear box. * Compact and light weight. * Standard supply voltage 1 phase 230V, optional voltage available

Elektriska Manöverdon (Electrical Actuator type ITQ 010-300)
Elektriska Manöverdon (Electrical Actuator type ITQ 010-300) Image

ELECTRICAL ACTUATOR TYPE ITQ 010-300 –  * Self locking – Provided by double worm gearing to keep position of valve unchanged against reverse torque from valve. * Motor – Specially designed induction motor to generate high starting torque and high efficiency equipped with thermal protector to prevent damage from over heating. * Torque switches – Protects actuator from damage caused by overload from the driven valve over the whole travel. 1 for each open/close. * Manual override – Auto / Manual switchable lever and hand wheel engagement for emergency manual operation. * Drive force automatically resorted by motor start, unless lever padlocked to prevent this occurring. * External mechanical stopper – Prevents over run of travel angle when limit switch fails. * Removable drive bushing and ISO5211 mounting base * (F07~F16) for easy mounting on valve.

Elektriska Manöverdon (Electrical Actuator type ITQ 600-900)
Elektriska Manöverdon (Electrical Actuator type ITQ 600-900) Image

ELECTRICAL ACTUATOR TYPE ITQ 600-900 –  * Self locking – Provided by double worm gearing to keep position of valve unchanged against reverse torque from valve. * Motor – Specially designed induction motor to generate high starting torque and high efficiency equipped with thermal protector to prevent damage from over heating. * Torque switches – Protects actuator from damage caused by overload from the driven valve over the whole travel. 1 for each open/close. * Manual override – Auto / Manual switchable lever and hand wheel engagement for emergency manual operation. * Drive force automatically resorted by motor start, unless lever padlocked to prevent this occurring. * External mechanical stopper – Prevents over run of travel angle when limit switch fails. * Removable drive bushing and ISO5211 mounting base. *  (F07~F16) for easy mounting on valve.

Backventiler
Backventiler (Non Return Valve GA 015, GB 015) Image
Backventiler (Non Return Valve GA 015, GB 015)
NON RETURN VALVE GA 015, GB 015, GB 019 – Little dimensions and low weights. Face to face acc.to DIN EN 558-1 Series 49 (DIN 3202 K4). Opening pressure from 20 to 500 mBar. Usable also as vacuum breacker, overpressure and bottom valve. No leackage with soft seat and acc.to DIN 3230 BN3 with metal seat. Low head losses.
Backventiler (Non Return Check Valve) Image
Backventiler (Non Return Check Valve)
CHECK VALVE FEATURES THAT THE PIPING ENGINEER IS LOOKING FOR.    * Tight shut off under minimum back pressure. * Quick response to no-flow or reverse flow conditions. Low resistance to forward flow. * Lightweight construction. * Ease of installation with unskilled operators. * No maintenance. It is a stop silent valve. * It stops the reverse flow and is completely silent in its operation, preventing water hammer.
Ångejektorer
Ejektor Image
Ejektor
Instantaneous Slurry Heaters – IOM
Smutsfilter
Strainer PN 20, Y-type, brass MS 58, 30 Bar Image
Strainer PN 20, Y-type, brass MS 58, 30 Bar
Strainer PN 20, Y-type with screwed ends and drain plug. Materials, Body: brass MS 58 Screen: stainless steel 1.4301 Connection: screwed ends DIN 259 Test pressures: 30 bar Specials: Brass fittings are not approved for use in drinking water installations!
Strainer 800 lbs (~ PN100), Y-type, forged steel A 105N, 205 Bar Image
Strainer 800 lbs (~ PN100), Y-type, forged steel A 105N, 205 Bar
Strainer 800 lbs (~ PN100), Y-type, screwed ends and drain-plug 1/2″ in cover. Materials, Body: forged steel A 105N, Screen: stainless steel AISI 316 Gasket: graphit reinforced Connection: screwed ends BSP Test pressures: 205 bar
Strainer PN 40 Y-type, with screwed ends, stainless steel 1.4408, 60 Bar Image
Strainer PN 40 Y-type, with screwed ends, stainless steel 1.4408, 60 Bar
Strainer PN 40 Y-type, with screwed ends Materials: Body: stainless steel 1.4408, Screen: stainless steel perforated plate 1.4408 Gasket: PTFE Connection: screwed ends BSP Test pressures: 60 bar
Strainer 800 lbs (~ PN 100), Y-type, stainless steel AISI 316, 205 Bar Image
Strainer 800 lbs (~ PN 100), Y-type, stainless steel AISI 316, 205 Bar
Strainer 800 lbs (~ PN 100), Y-type, screwed ends and drain-plug 1/2″ in cover. Materials: Body: stainless steel AISI 316. Screen: stainless steel AISI 316. Gasket: graphite reinforced. Connection: screwed ends BSP. Test pressures: 205 bar.
Strainer PN 63 Y-type, butt-weld-ends, cast steel GP 240GH), 96 Bar Image
Strainer PN 63 Y-type, butt-weld-ends, cast steel GP 240GH), 96 Bar
Strainer PN 63 Y-type, butt-weld-ends and drain-plug 1/2″ in cover. Materials: Body: cast steel GP 240GH). Screen: stainless steel 1.4301. Gasket: graphit reinforced. Connection: butt-weld-ends DIN 3239 Form C. Test pressures: 96 bar.
Strainer PN 160 Y-type, butt-weld-ends, cast steel GP 240GH), 240 Bar Image
Strainer PN 160 Y-type, butt-weld-ends, cast steel GP 240GH), 240 Bar
Strainer PN 160 Y-type, butt-weld-ends and drain-plug 1/2″ in cover. Materials: Body: cast steel GP 240GH). Screen: stainless steel 1.4301. Gasket: graphit reinforced. Connection: butt-weld-ends DIN 3239 Form C. Test pressures: 240 bar.
Kulventiler
3-pieceType A20D/AF20D / DN10-DN100 / 3/8"-4" (3-Piece Ball Valve) Image
3-pieceType A20D/AF20D / DN10-DN100 / 3/8"-4" (3-Piece Ball Valve)
3-PIECE BALL VALVES SERIES A20D / AF20D with full or reduced bore antistatic, with ISO-top flage for direct mounting of an actuator. Stainless steel 1.4408 / CF8M Carbon steel 1.0619 / A216 WCB
2-piece Type AF90D / DN15-DN100 long pattern (Flanged Ball Valves) Image
2-piece Type AF90D / DN15-DN100 long pattern (Flanged Ball Valves)
2-pieces DIN-Flanges Ball Valve long pattern,  full bore.  with double Gasket System FireSafe acc. BS6755 Part2. , TA-Luft and SIL 2 tested and FDA conform. Antistatic, with ISO connection for direct mounting for Actuator. With locking device.
2-piece Type AF94D / DN15-DN100 short pattern (Flanged Ball Valves) Image
2-piece Type AF94D / DN15-DN100 short pattern (Flanged Ball Valves)
2-pieces DIN-Flanges Ball Valve short pattern, full bore.  with double Gasket System FireSafe acc. BS6755 Part2. , TA-Luft and SIL 2  tested and FDA conform. Antistatic, with ISO connection for direct mounting for Actuator. With locking device.
Type 80D / DN15-DN100 Image
Type 80D / DN15-DN100
Wafer type A80D ball valve with full bore, with ISO mounting pad for direct mounting of pneumatic or electrical actuator. FIRESAFE-design (with graphite gaskets) and antistatic device.  With locking device
3-piece Type JBSM / DN15-DN50 / 1/2"- 2" (metal seated ball valve) Image
3-piece Type JBSM / DN15-DN50 / 1/2"- 2" (metal seated ball valve)
3-piece metal seated ball valve, full bore, antistatic device with ISO-mounting pad for mounting of pneumatic or electric actuators. With locking device
V-Port Segment Type JSB / DN25 - DN400 / 1 (metal seated ball valves) Image
V-Port Segment Type JSB / DN25 - DN400 / 1 (metal seated ball valves)
1-piece Trunnion Design DIN PN16/40, or ANSI class150/300, DIN sizes  DN25 – DN400 and ANSI  1inch – 16inch, for Control- or Shut off – Applications, soft- and metal seated Design, with ISO mounting pad acc. ISO5211, anti-blowout-system, Antistatic, Face to Face dimensions acc. ISA S75.04. For Applications up to 350°C.
Floating Type JBFM / DN15-DN250 / 1/2"-10"(metal seated ball valves) Image
Floating Type JBFM / DN15-DN250 / 1/2"-10"(metal seated ball valves)
2-pieces metal seated DIN-/ANSI Flange Ball Valve PN16/40, ANSI class 150 – 300, DIN-Face to face dimension acc. EN558-1, row 27 or ANSI-dimensions, PN100/class 600 on request, full port. FireSafe acc. nach ISO 10497 certified. Antistatic, with ISO connection for  Actuator mounting kit. With locking device. Different body materials and designs available for applications up to 550 ° C.
Kägelventiler
Kägelventiler Protek-2430 DN 15-25 (Globe Valve bellows sealed with flanges) Image
Kägelventiler Protek-2430 DN 15-25 (Globe Valve bellows sealed with flanges)
GLOBE VALVE – Cat 218M, Cat 450M bellows sealed with flanges.
Kägelventiler 2430 DN 32-100 (Globe Valve bellows sealed with flanges) Image
Kägelventiler 2430 DN 32-100 (Globe Valve bellows sealed with flanges)
GLOBE VALVE – Cat 218M, Cat 222M bellows sealed with flanges
Pneumatiska ställdon med tillbehör
Pneumatic Actuators Type 1, Features & Benefits Image
Pneumatic Actuators Type 1, Features & Benefits
Pneumatic Actuators Type 1 Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR). Body of Anodized Aluminum in black colour as standard, other finishes avialable. This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 ... Read More
Pneumatic Actuators Type 1, 0 -90º WM 1 Image
Pneumatic Actuators Type 1, 0 -90º WM 1
Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR). Body of Anodized Aluminum in black colour as standard, other finishes avialable. This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR
Pneumatic Actuators Type 1, WM 2, 4, 8, 12, 20 and 35 Image
Pneumatic Actuators Type 1, WM 2, 4, 8, 12, 20 and 35
Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR). Body of Anodized Aluminum in black colour as standard, other finishes avialable. This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR
Pneumatic Actuators Type 1, WM 250 Image
Pneumatic Actuators Type 1, WM 250
Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR). Body of Anodized Aluminum in black colour as standard, other finishes avialable. This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR
Pneumatic Actuators Type 1, WM 400 Image
Pneumatic Actuators Type 1, WM 400
Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR). Body of Anodized Aluminum in black colour as standard, other finishes avialable. This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR
Pneumatic Actuators Type 1, 0 -90º Technical Data, summary Image
Pneumatic Actuators Type 1, 0 -90º Technical Data, summary
Compact rack and pinion actuator, Type 1, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR). Body of Anodized Aluminum in black colour as standard, other finishes avialable. This actuator is generally recommended to ”small” Butterfly valves and all types of Ball valves. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR
Pneumatic Actuator Type 1, 0 -180º, WM 4, 8, 12, 20 and 35 & Technical Data, summary Image
Pneumatic Actuator Type 1, 0 -180º, WM 4, 8, 12, 20 and 35 & Technical Data, summary
Compact rack and pinion actuator, Type 1, for half turn movement and modulating, only available as Double Acting (DA). Body of Anodized Aluminum in silver colour as standard. This actuator is generally recommended to for use with thee way valves with rotary motion between 0-180º turning angle. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMUR.
Chemically Nickel Impregnated Actuators Type 1, CNI Image
Chemically Nickel Impregnated Actuators Type 1, CNI
The high density Nickel Alloy that is used and the added PTFE gives the actuators more resistance to chemical attacks and improves the lifespan. The production process makes it possible to impregnate also all internal surfaces of the CNI actuators. From the beginning it was specifically developed for the Food, Beverage and Pharmaceutical industries, now approved by FDA (Food and Drug Administration, USA) for use in the Food & Beverage Industries. Increased cor... Read More
Pneumatic Actuators Type 2, Features & Benefits and Body Adaptor Kit Image
Pneumatic Actuators Type 2, Features & Benefits and Body Adaptor Kit
Body Adaptor Kit, BAK Type 2 has a unique design, it is fitted with a BAK (Body Adaptor Kit). The integral Body Adaptor Kit, which is interchangeable with a wide range of valves (metric, imperial or customer designed) for direct mounting by using an interchangeable insert sleeve. The Kit contains body adaptor, sleeve, key, stop adjustment bearing, circlip, bolts and screws. Stainless Steel Sleeves All Driveshaft’s in WM Actua... Read More
Pneumatic Actuators Type 2, WM 35, 55, 70, 100 and150 Image
Pneumatic Actuators Type 2, WM 35, 55, 70, 100 and150
Pneumatic Actuators Type 2 Compact rack and pinion actuator, Type 2, for quarterturn movement and modulating, Double Acting (DA) or Spring Return (SR). Body of Anodized Aluminum in black colour as standard, other finishes avialable. This actuator is generally recommended to ”large” Butterfly valves. The actuators comply fully with all the relevant industry standards for interfaces and connections such as ISO 5211, DIN 3337, VDI/VDE 3845 and NAMU... Read More
Urkopplingsbar Handväxel (Manual Override Gear) Image
Urkopplingsbar Handväxel (Manual Override Gear)
Manual Override with declutch mechanism for Double Acting (DA) and Spring Return (SR) pneumatic actuators. For TT Actuators, movement 0-90º size: ITG-050: DA size 8 to 35 ITG-050: SR size 8 to 20 ITG-060: DA size 35 to 55 ITG-060: SR size 35 ITG-080: DA size 70 to 150 ITG-080: SR size 55 to 70 ITG-100: DA size 250 ITG-100: SR size 100 to 150 MOR-5100: DA size 400 MOR-5100: SR size 250
Digital Positioner PMV Type D3 Image
Digital Positioner PMV Type D3
Digital Positioner Type D3 Digital positioners, often with the display and keypad to enter settings. Advantages are that the auto calibration setting is accurate regardless of who makes the calibration
Pneumatic Positioner PMV Type P5 Image
Pneumatic Positioner PMV Type P5
Pneumatic Positioner Type P5 For single or double acting application, this modular design allows for the simple addition of I/P converters and/or a feedback unit with a variety of feedback options
Electropneumatic Positioner PMV Type EP5 Image
Electropneumatic Positioner PMV Type EP5
Electropneumatic Positioner Type EP5 This compact and sturdy unit is designed for maximum performance in all types of environments. The EP5 is available in Standard, Intrinsically Safe and Explosion Proof versions
Feedback unit F5 for Positioners Type P5 and EP5, 4-20 mA or Potentiometer Image
Feedback unit F5 for Positioners Type P5 and EP5, 4-20 mA or Potentiometer
Feedback unit Type F5 For position feedback to P5 and EP5, the F5 unit offers the ability to change switches between mechanical and proximity, a potentiometer or a 4-20 mA transmitter to the P5 base pneumatic positioner. The IP66 modular housing needs no special mounting pieces and is O-ring sealed. F5 mounts direct on top of P5/EP5 positioner.
Feedback unit F5 for Positioners Type P5 and EP5, Endstop indication Image
Feedback unit F5 for Positioners Type P5 and EP5, Endstop indication
Feedback unit Type F5 For position feedback to P5 and EP5, the F5 unit offers the ability to change switches between mechanical and proximity, a potentiometer or a 4-20 mA transmitter to the P5 base pneumatic positioner. The IP66 modular housing needs no special mounting pieces and is O-ring sealed. F5 mounts direct on top of P5/EP5 positioner.
Pneumatic Positioner type QS-P2G-LT-RE Image
Pneumatic Positioner type QS-P2G-LT-RE
QS-P2G-LT-RE Remote mounted, External contactless hall effect feed-back with 2 meter cable. No visual position indicator or display. Analogue input: 1, V or mA Manual function, open/close Consoles & 7-pol IP67 (FM) connector for Supply & Analogue signals not included. Supplier Pat No: PKV-7129